Woodworkers:
3 signs your vacuum pump is failing
...AND WHY YOU SHOULDN’T IGNORE THE PROBLEM
Is your CNC machine playing up? Worried you’ll need to replace the whole thing? Tired of wasting wood due to repeated cutting issues?
We’ve got good news. It might not be a fault with the machine itself. It’s unlikely it’s the materials you’re using - and there’s nothing wrong with your skills as a woodworker.
The problem might be your vacuum.
A poor, weak or inadequate vacuum can cause a whole host of problems that often get blamed on other reasonings. So, if you’re experiencing any of these issues, then your vacuum pump should be the first thing you investigate:
1. Poor quality cuts
If your vacuum is weak, your boards can slip during cutting, resulting in poor quality, irregular or inaccurate cuts. This results in wastage, which could otherwise be avoided.
2. Chipping of boards
If your vacuum isn’t holding your board in place with enough force, and the boards move or vibrate during machining, this can cause the board to chip. Again, this causes wastage that could otherwise be avoided.
3. Damaged tooling
A poor vacuum can lead to increased vibration, which can cause damage to tooling. Not only does this mean extra cost in repairing or replacing parts, but it can also delay production or cause unplanned downtime.
THE COST TO YOUR BUSINESS
If you’re worried about the cost of replacing your vacuum, don’t be. While there might be an initial cost to investing in quality parts, the cost of not investing will be much higher.
In wastage
Chipped boards and inaccurate cuts mean wasted materials. Even if you’re only experiencing problems every now and then, these will still add up, and the problem will only get worse.
In running and maintenance costs
Damaged tooling means replacement parts, and replacement parts cost money. On top of this, an inefficient pump will be using way more energy than it should, adding to your energy bill (and your carbon footprint).
In downtime
If a vacuum pump is down, the machine cannot operate, resulting in unplanned downtime. This will impact the progress of any current jobs, costing you money, but also your reputation. Ignoring your pump problems is like throwing money away, so it pays to resolve the issue quickly.
WHAT’S CAUSING THE PROBLEM?
There are many variables that could be contributing to a poor vacuum, and it is sometimes difficult to identify the issue. But the good news is, if you can figure out the problem, you might not need a new pump at all.
Dust and debris
The issue could be as simple as a build-up of dust and debris. Make sure you clean your spoil boards, router tables and seals before the placement of new workpieces.
Incorrect set-up
The way your machine is set up could be causing the issue. For example, if gaskets aren‘t cut and fitted correctly, the tolerance between ends might be too high, affecting your vacuum pressure.
Leak in the vacuum system
If you have a leak in your vacuum process, this will most certainly be causing problems with your vacuum pressure.
Lack of servicing
Poor maintenance of the filter unit will increase the pressure loss over the filter, resulting in a reduced vacuum level. It could also lead to filters rupturing and damaging the pump.
Wrong type of pump or filter
For fine composite materials, some vacuum pumps need a filter with a lower micron rating. Without the correct filter, some particles may enter and potentially damage the pump‘s internal mechanics.
ACTIONS YOU CAN TAKE
The first priority should be making sure your vacuum equipment is fit for purpose and as energy efficient as possible. Overkill vacuum solutions are commonly used and, although you may not notice any issues with performance, these solutions could be resulting in a lot of wasted energy.
To maximise energy efficiency, you can use a pump with a variable frequency drive. This can be an effective way of reducing energy costs by up to 25%.
Depending on the machinery and the required operations, your vacuum could be better utilised with a Rotary Claw pump rather than Vane. Becker Claw pumps have been designed for minimal noise emissions, keeping your production area quieter too.
Once you’ve got the right vacuum system in place, servicing and maintaining it is your next priority. Becker yearly services are carried out by expert engineers, and we only use genuine Becker parts. Our engineers are also available on a 24-hour call-out to keep your machines operating around the clock.
Follow us: